Liquid Cast™ Deep Pour Epoxy Resin
Liquid Cast™ Deep Pour Epoxy Resin is a two part clear casting epoxy resin system formulated for encapsulating and deep pour casting projects. This product can be poured between a half inch and up to two inches in one pour with little to no trapped air.
Liquid Cast™ Deep Pour Epoxy Resin is the perfect choice for flower preservation, river tables, charcuterie boards, and many other casting projects which require layers of epoxy resin over half of an inch.
Note: Liquid Cast Deep Pour is not intended for use with small jewelry items, shallow pours, or as a coating system. Pours under 1/2" may remain flexible.
Mixed Viscosity: 850 CPS
✔️ 45+ Minute Working Time
✔️ Dry in 12-24 Hours
✔️ Excellent Air Release
✔️ 1:1 Mixing Ratio by Volume
✔️ High Gloss Finish
✔️ Made in the US
✔️ Low Viscosity
✔️ No VOC
Step 1. Prepare for Mixing
Gather your epoxy resin, mixing supplies, and personal protective equipment. We recommend at the very least using nitrile gloves, safety glasses, clothing to protect from spills. Be sure to use epoxy resin in a well-ventilated room or use an air-purifying respirator.
Step 2. Calculate Coverage Area
Using a tape measure, measure the length, width, and depth of your mold and then input this information into the Epoxy Resin Coverage Calculator to determine how much epoxy resin you will need to fill the mold.
Step 3. Pour Epoxy Resin into a Mixing Container
Measure your desired amount of epoxy resin at a 1:1 ratio by volume into a graduated mixing cup. Pour the resin first, allow it a moment to settle, and then follow up with an equal amount of hardener.
Step 4. Mix Thoroughly for Four Minutes
Mix the two parts together for a total of four minutes. Be sure to scrape the bottom and sides of the container while mixing so that there is no un-mixed epoxy resin. Aggressive mixing can introduce excessive air, stir slowly but thoroughly. Continue to stir until the epoxy resin no longer has ribbons and returns to clear.
Step 5. Pour into Mold
Pour the epoxy resin slowly into your mold in 1/4" increments. To minimize trapped air in your project pour in 1/4" increments, allow 1-2 minutes for air to surface, sweep your torch or heat gun over the surface to pop any bubbles, and repeat until you reach your desired depth.
Liquid Cast Deep Pour Epoxy Resin is not meant for shallow pours under 1/2" unless poured in layers. If poured under 1/2" the epoxy resin could remain flexible (depending on the mass and volume of the pour).
In most cases we recommend pouring at 1/2" to 1" to ensure the epoxy resin does not overheat during the curing process. It is better to start small and add layers as necessary than pour too much at once. Larger pours should be poured in smaller layers to prevent air entrapment and overheating.
Step 6. Use a Torch or Heat Gun to Remove Trapped Air
Quickly sweep a propane torch or heat gun across the surface being sure to keep the flame 6-8 inches away from the surface. Do not overheat the epoxy resin or hold the heat in one spot for too long. We recommend heating the epoxy resin only during the working time, do not apply heat once the working time has passed. After eliminating bubbles allow the epoxy resin time to cure in the appropriate environment (listed in Technical Data below).
Ensure that you are working in a well-ventilated room or using an air-purifying respirator.
Common Product Uses
Automotive Shift Knobs
Ideal Curing Temperature - 65°F - 80°F
Working Time - 45 Minutes
Dry to Touch - 12-36 Hours
Full Cure - 3-7 Days (Depending on volume and mass of pour)
Maximum Recommended Coating Thickness - Not intended for use as a coating system
Maximum Recommended Casting Thickness - 2" per layer
Temperature Resistance - 475°F
Shelf Life (Unopened) - 12 Months
Shelf Life (Opened) - 6 Months (Depending on environment)
Shore D Hardness - 60-70
32oz Kit = 16 ounces Resin + 16 ounces Hardener
64oz Kit = 32 ounces Resin + 32 ounces Hardener
1 Gallon Kit = 64 ounces Resin + 64 ounces Hardener
2 Gallon Kit* = 128 ounces Resin + 128 ounces Hardener
* (Shipped in multiple 64oz Containers for ease of use, may be occasionally sent in 128oz containers if 64oz containers are unavailable at the time)
I am pretty thrilled to have tried this resin. I experienced very few bubbles and it's such a blessing. I was a bit nervous because my molds can be deep in certain areas and shallow in others. For example, I pour cat heads. The face is deep but the ears are shallow. To my joy, I unmolded my test pieces this morning and everything came out great! Everything set up beautifully.......yup.....even the ears. I still found a few bubbles but it's nothing I can't fix. The only con I have to report, is that my glow pigment doesn't mix well with the resin. It tends to puddle at the bottom of my cup. But that isn't a major issue and I can deal with it.
I love it, works perfect, so clear!
By far the best deep pour resin I have tried! The consistency, low odor, barely any bubbles. I've only tried 1 other deep pour from another brand but I won't go back to it. Kresin is the best in my opinion.
I know with this epoxy I get crystal clear results every time. It’s worth the price. The quality is great 😊
Liquidity Split is the best 24 hour cure epoxy on the market. We couldn't run our business without it. We consistently have cups that are dry to the touch in 2 hours or sooner (we work really hot), so we can keep moving.
This stuff is so good. I think this will be the resin I incorporate into my business. And over the last few yrs I have tried dozens of resins. And this by far the one I believe is gonna sell my art. Customer service is great to. They responded quick. Thanks again
Deep Pour is what I exclusively use for my bridal bouquet preservation. The product is amazing and I absolutely love it. Shipping is quick and Homestead Weddings and Events appreciates KS resin so much. Thanks y’all!
I used the Cast Deep Pour resin in my "caring hands" mold and they turned out great!
Liquid Cast™ Deep Pour Epoxy Resin