Liquid Stone Elite™ Table Top Epoxy Resin
Liquid Stone Elite™ is a two part clear epoxy resin system formulated for coating bartops, tabletops, and countertops. If you are looking for a premium epoxy resin that cures water-clear, has excellent durability, cures rock hard, has high temperature resistance, and offers excellent UV resistance Liquid Stone Elite is for you.
Liquid Stone Elite™ is a thinner viscosity than Liquid Stone™ and Liquid Stone Ultra UV™, and has a significantly longer working and drying time.
This product does not require a UV light to cure.
Mixed Viscosity: 2800 CPS
✔️ 60+ Minute Working Time
✔️ Dry in 12-18 Hours
✔️ 1:1 Mixing Ratio by Volume
✔️ High Gloss Finish
🔥 High Temperature Resistance
☀️ Industry Leading UV Resistance
✔️ Made in the US
✔️ No VOC
Step 1. Calculate Surface Area and Check Level
Using a tape measure, measure the square feet of your surface (Length x Width) and then input this information into the Epoxy Resin Coverage Calculator. If you plan to do a dirty pour or add colorant, you may want to increase the required epoxy resin by 5-25%. After calculating the amount of epoxy resin that your project will require, make sure that your surface is completely level and adjust as needed. A level surface is very important.
Step 2. Prepare for Mixing
Gather your epoxy resin, mixing supplies, and personal protective equipment. We recommend at the very least using nitrile gloves, safety glasses, clothing to protect from spills. Be sure to use epoxy resin in a well-ventilated room or use an air-purifying respirator.
Step 3. Cover Cabinets and Floors with Plastic
Before applying epoxy resin to the surface utilize plastic sheeting to cover any surfaces that epoxy resin could get on. We recommend applying tape to the backsplash/wall, plastic on the floor, as well as plastic covering all cabinets. Be mindful of where you walk to ensure you do not track epoxy resin outside of your work area.
Step 4. Pour Epoxy Resin into a Mixing Container
Measure your desired amount of epoxy resin at a 1:1 ratio by volume into a graduated mixing cup. Pour the resin first, allow it a moment to settle, and then follow up with an equal amount of hardener.
Step 5. Mix Thoroughly for Four Minutes
Mix the two parts together for a total of four minutes. Be sure to scrape the bottom and sides of the container while mixing so that there is no un-mixed epoxy resin. Aggressive mixing can introduce excessive air, stir slowly but thoroughly. Continue to stir until the epoxy resin no longer has ribbons and returns to clear.
Step 6. Apply to Surface
Apply the epoxy resin to your surface immediately after mixing. You can do this by using your gloved hand, a foam roller, a brush, a trowel, and many other tools. Make sure that epoxy resin completely covers the surface. Using your gloved hand or spreading utensil, apply epoxy resin to the sides of the surface (if necessary).
If you do not apply enough epoxy resin it may pull away from the edge. If you apply too much epoxy resin it can drip off or run to one end depending on the surface.
Step 7. Use a Torch or Heat Gun to Remove Trapped Air
Quickly sweep a propane torch or heat gun across the surface being sure to keep the flame 6-8 inches away from the surface. Do not overheat the epoxy resin or hold the heat in one spot for too long. We recommend heating the epoxy resin only during the working time, do not apply heat once the working time has passed. After eliminating bubbles allow the epoxy resin time to cure in the appropriate environment (listed in Technical Data below).
It is very important that the epoxy resin has a consistent curing temperature throughout the entire curing process. Keep in mind that curing the epoxy resin in a warmer environment will yield a more durable surface. We recommend a maximum of 120° F and a minimum of 75° F.
Ensure that you are working in a well-ventilated room or using an air-purifying respirator.
Tip: Hate those pesky drips? Wait a couple of hours after applying the epoxy resin and return with a spreader or knife and push the tool up against the bottom of the surface while simultaneously pulling the tool from side to side at a slight angle. The epoxy resin will have thickened up enough where it will no longer drip and you will not need to sand the drips off the following day.
Step 8. Apply Additional Layers
We recommend applying at least two layers of epoxy resin for added surface protection. There are two ways of adding additional layers of epoxy resin to the existing layer.
1. Apply the next layer while the last layer is still tacky to the touch. Allow the first layer to dry for 3-6 hours and lightly touch it with a gloved hand. If the epoxy resin coating feels tacky without pulling up like taffy, you can apply an additional layer at this time. Applying an additional layer while the previous layer is still tacky gives you a chemical bond.
2. Apply the next layer after the last layer has dried for 24 hours. Lightly sand the last layer with 220 grit sandpaper, remove any debris from sanding, and apply an additional layer starting with Step 1. Applying an additional layer after sanding will give you a mechanical bond.
Both methods are excellent options for applying additional layers. The chemical bond will allow you to complete your project faster, while the mechanical bond may allow you to remove any surface imperfections before the final coat.
Stainless Steel Tumblers
Surfaces that require a durable top-coat
Ideal Curing Temperature - 75°F - 80°F
Working Time - 60+ Minutes
Dry to Touch - 12-18 Hours
Full Cure - 72 Hours
Maximum Recommended Coating Thickness - 1/8"
Maximum Recommended Casting Thickness - 1/4"
Temperature Resistance - 500°F
Shelf Life (Unopened) - 12 Months
Shelf Life (Opened) - 6 Months (Depending on environment)
Shore D Hardness - 76
64oz Kit = 32 ounces Resin + 32 ounces Hardener
1 Gallon Kit = 64 ounces Resin + 64 ounces Hardener
2 Gallon Kit* = 128 ounces Resin + 128 ounces Hardener
* (Shipped in multiple 64oz Containers for ease of use, may be occasionally sent in 128oz containers if 64oz containers are unavailable at the time)
I use this product for making resin soap dishes and am very pleased with the results.
This resin gives a good solid finish like glass. Some I’ve used give an almost plastic like finish that easily scratches. This is AAA stuff!
Liquid Stone Elite™ Table Top Epoxy Resin
I did pour on an extremely hot day, but the resin was like water. So smooth. My project was a lazy susan. Very few bubbles. Since bottles, glasses, salt and pepper containers, and whatnot would be placed on the susan, I wanted a harder surface to avoid dents. Still in the curing stage at this point. Very pleased with this resin so far. Next I will be using the table top resin on two end tables. Thanks for producing this wonderful product.
I used liquid stone elite on a paint palette project recently and it was so clear and shiny! It was clear like glass without a bubble in sight! I highly recommend this product.
I admit I tried other resins but when I found KS Resin the search for great epoxy was over. I love all their resin but I’m a devoted liquid stone elite user. It has never failed me. It dries beautifully, is hard and heat resistant. Plenty of pot time to get your project done. You won’t be disappointed.
Nice thickness and super clear , gives a good amount of working time - I’ll definitely purchase this again .
Delivery was fast, but had some of the Resin that had spilled in box during shipping. I contacted KSResin and was immediately sent out more than enough resin to replace amount that was spilled. Customer service is awesome! Since then I have used this on lots of projects. Stonecoat was my resin of choice, but now it is KSResin.
I was close to abandoning this brand after a poor experience with a previous version of the liquid stone epoxy which was too viscous to work with. This version is much better. It gives a long working time and it releases the bubbles better. Nice improvement.
I use it on my tiles and table tops and there are barely any bubbles, I torch a couple of times and they are gone. The finish is beautiful.